Pro-tek Frame Slider Swing Arm Spool Kit and 23 similar items

Pro-tek Frame Protector Slider Swing Arm Spool Slider Kit Suzuki 2001 2002 2003 GSXR600 Black *Comes Complete with 1 Set(2) Frame Sliders 1 Set(2) Swing Arm Spool Sliders* Pro-tek frame sliders spool sliders are made from an acetal resin for strength and durability Helps protect your frame and swing arm from nasty spills and tip overs. Pro-tek swing arm sliders are designed to act as swing arm stand buttons and give the swing-arm extra protection in case of a crash. No Modifications required of fairings on this set. Comes complete with instructions for easy installation. Comes with all mounting hardware. Frame sliders are not designed to protect the plastics, rearsets (footpegs), or clipons (handlebars). They are designed to absorb the impact and energy of a fall so that you don't damage your engine or frame. Those two parts of the bike are critical components for racers and an insurance company as they will often total your bike if those are damaged. Frame sliders come in two basic models which are cut or no cut frame sliders. A cut frame slider means that you have to cut your plastics to be able to bolt that type of frame slider on to your bike. No cuts obviously mean you do not have to cut a hole in your plastics. We like each model to have to cut a 2" hole in your plastics and other kits with no modifications you do not have to cut anything. The no cut kit normally has brackets that you mount up below your plastics that then go to a place where there are no plastics then you bolt on the slider to that plate. Basically the plate lets you relocate where the slider will bolt on. No cut sliders are also more expensive. Now for quick bullet points about sliders: 1. They are not designed to protect plastics, clipons, or rearsets, even though they might help sometimes. 2. You do not want a slider to stick out too far or it will help flip your bike in a crash by snagging on the ground, curb or anything else. 3. You want delrin or plastic to touch down when you crash as they will grind off and not catch on anything and if hit hard enough or direct enough they will shatter. 4. If your slider shatters, grinds off or bends then it did it's job. You don't want it solid after a crash or it didn't absorb any energy but merely transfered it on to what you bolted it to. 5. When f1 cars hit the side of a track they explode as they don't want the drive to absorb the energy. Frame sliders are the same way. You want them to stay attached but get beat up and take the energy. 6. If the bolt on a frame slider bends that's a good thing as the only other option is to put the energy on the frame or mounting point. Better the bolt bends. Also if it didn't bend it might have flip the bike by snagging something. A mangled frame slider, but still on the bike, did it's job. 7. No cut frame sliders aren't a direct bolt on like cut sliders as they often have a bracket. We hope this information was helpful and if you have anything to add or questions then feel free to contact us. Ride safe and hope you never have to use your frame sliders. Suzuki '01-'03 GSXR600 The frame sliders are to be mounted to your upper engine mount bolts. Refer to your service manual before performing this installation. Before beginning, make sure pinch bolts are tight to prevent any engine movement. Remove right side engine mount bolt and install notched slider with supplied 10mm x 1.25 x 90mm bolt. Remove left side engine mount bolt and install mounting bracket. Use the supplied 10mm x 1.25 x 70mm bolt. Install slider into bracket with the 10mm x 1.5 x 30mm bolt. Always torque bolts to factory specifications. Includes: (2) Acetal pucks with aluminum bushings (1) Aluminum mount bracket (1) 10mm x 1.25 x 90mm bolt (long puck and right side) (1) 10mm x 1.25 x 70mm bolt (bracket through bolt) (1) 10mm x 1.5 x 30mm bolt (attach flat puck to bracket) Track Page Views With Auctiva's FREE Counter