Fast Shipping On All Items 30 Days Money Guarantee Customer Support Excellent Service 100% Satisfaction Satisfaction Guaranteed 8-34Mm Rebar Tying Machine Rebar Tying Tool, Automatic Rebar Tie Wire Twister Rebar Tie Tool W/Pliers + 2 X Batteries, Rebar Tier Tying Machine for Steel Bar Rod Tying Binding, Orange Specification Part Number MLLCR-3159 Batteries Required? Yes Battery Cell Type Lithium Ion Item Weight 7.65 pounds Batteries 2 12V batteries required. (included) Batteries Included? Yes Size Orange 8-34mm Package Dimensions 17.01 x 13.54 x 4.49 inches Manufacturer CBDYQ_US 13.54 inches x 17.01 inches x 4.49 inches. Weight: 7.65 lb Item Description Important Parameters: Knot Number per Charge: 1500 times | Strapping Range: 8-34mm | Single Strapping Time: 0.8s | Battery Capacity: 4500 mAh | Wire Length: 300-500mm | Charging Time: 1.5h | Voltage: 12V. 0.8S for Each Knot: The binding efficiency is increased by 2-4 times compared with the old version, and it takes only 0.8 seconds to tie a wire knot. Using this tool, one machine can easily replace the work of 3-4 laborers, saving time and energy while increasing overall productivity. 2 x 4500mAh Battery: With 2 x 4500mAh large capacity battery that can be fully charged in just 1.5 hours, this rebar tie gun allows for extended periods of use without the need for constant recharging. Wide Range of Applications: Can be used for buildings, bridge engineering, highway tunnels, mine construction, floor pipe, heating floor mesh, steel bar, etc. Note: Upon installing the coil for the first time, it is recommended to test the knot several times to ensure proper function. If the wire is not coming out, it may indicate that the coil was not installed properly. Product Description Automatic Rebar Tier Tying Machine W/2 Batteries Rebar Tier Is a Hand Held Machine Used to Pack Rebars Quickly. It Is a Miniature Motor Tool Has the Trait of Safety and Credibility. Used for Building Market, Including Civil Building, Floor Pipe, Heating Floor Mesh, Steel bar, Etc. Compact Size Lightweight Save 3-5 Times Reasonable Structure Advanced Craft Simple and Convenient Operation High Efficiency Easy to Grab Convenient Maintenance Package Included 1x Tying Machine 1x Pliers 1x Charger 1x Storage Box 2x Lithium Ion Batteries 1x Tying Wire in the Machine (Tying Wire Standard: About 0.8 Mm X 110 M/Roll) Specifications Color: Blue/Orange?for Choice) Material: Plastic + Metal Voltage: 12V Battery: Lithium Ion Batteries Battery Capacity: 4500 Mah Battery Charging Time: 1.5 Hours Full Filling Tying Wire Diameter: 0.8mm Tying Wire Length: More than 110 M Applicable Scope of Steel Strapping: 8mm - 34mm Notice Please Allow 1-3cm Error Due to Manual Measurement and Make Sure You Do Not Mind Before Ordering. Please Understand That Colors May Exist Chromatic Aberration As the Different Placement of Pictures. Knot Wire Length: 300 - 500mm Knot Number per Charge: 1500 Times Knot the Required Time: 0.8 Seconds at a Time Machine Size: 275 Mm * 65 Mm * 240 Mm / 10.83''X2.56''X9.45''(Appr.) Tool Box Size: 42cm (16.54inch) *30cm (11.81inch) *10cm (3.94inch) Tying Wire Installations In the state of start-up, press the locking plate of the opening wire plate, open the plate cover. Take out the tying wire, tear the packaging film, pull straight wire head about 10 cm, load into the binding machine in the clockwise direction, the wire head into the guide tap tube.(Note: Clench the Wire Plate When Tear the Packaging Film, Do Not Let the Wire Loose. If the Wire Is Free to Disperse, It Will Lead to the Spread of the Wire Stuck in the Wire Plate.) Insert the head of the wire guide into the tap pipe until it is resisted. Cover the plate and fasten the locking piece. Pinch the wire forward with two fingers, press and hold the switch and send the wire out. If you want to take out the wire plate when finished, press and hold the locking piece, open the wire plate cover plate, holding the wire tray to the side and pull out. Operation Instructions The rebar tirer's jaws are stuck to the intersection of the steel bars, and the steel bars are hooked at 45 degree angles.(Note: There Can Be No Barrier Between the Mouth of the Jaws and the Wire.) Press the start switch, the rebar tirer machine carries on the work-spins, hinges tightly, cuts off. (Note: Press One Button at a Time, Do Not Probe the Jaws at Work.) When automatic completion, the jaw from the steel bar intersection and then pull back, complete the process and prepare for the next binding. When the binding process is not completed, do not unplug the machine in advance, otherwise it will cause the bundling of the goods tied skidding. Operating Skills In use, the left tilt 45 degrees after banding, the next time the banding into a right tilt 45 degrees banding, left and right alternately banding. When the machine is about to tighten, the machine will appear slightly shaking, while holding the hand of the machine not too tight, you can relax properly. Maintenance Clean the machine regularly, keep the wire mouth clean. This product can not be placed randomly, so as not to cause damage to parts. Batteries must not be placed together with other metal objects to avoid short circuit. Non-professional do not disassemble the machine arbitrarily, lest cause damage. When you encounter an unresolved failure, please give it to the professional repair. Return Policy ? We guarantee against any defective or misrepresented products. The original shipping label must be sent back to us to validate the return. A full refund can only be issued during the first 30 days upon receipt of the product. ? Returns will be voided if the product is mishandled or physical damaged by customer. ? Buyer will be responsible for all kind of return shipping/shipment to the seller for resolving the problem. ? Returns made for all non-defective, undamaged products are subject to a 15% restocking fee. Shipping and handling fees are absolutely non-refundable. If an item is returned to us due to an address issue, we do charge a reshipping fee to reship. If you would like a refund, there will be a 15% restocking fee applied. ? All returned products need to be assigned an RMA # (Return Merchandise Authorization #) prior to return. Please contact us through's messaging system to obtain an RMA# for the return. Any returned product without an RMA # on package will not be accepted or processed. ? Please contact us before returning. Feedback ? We appreciate your feedback and our system will automatically leave feedback for you after bid ends. ? Please contact us through message center if you have any problems, we will always try our best for 100% customer satisfaction. Payment Options Shop With Confidence